Packaging machine maintenance

Sep 03, 2023

1. The vacuum packaging machine should be used in an environment with a temperature of -10 ℃ -50 ℃, a relative humidity of not more than 85%, and no corrosive gases, dust, or explosive hazards in the surrounding air. Like the packaging machine and shrinking machine, this vacuum packaging machine uses a three-phase 380V power supply.
2. To ensure the normal operation of the vacuum pump for the vacuum packaging machine, the vacuum pump motor is not allowed to reverse. The oil level should be checked frequently. The normal oil level should be at 1/2-3/4 of the oil window (not exceeding). When there is water in the vacuum pump or the oil color turns black, a new oil should be replaced (usually once every two months of continuous operation, using 1 # vacuum gasoline or 30 # gasoline or engine oil can also be used).
3. The impurity filter should be frequently disassembled and cleaned (usually once every 1-2 months, and the cleaning time should be shortened for packaging debris).
4. For continuous operation of 2-3 months, the back cover should be opened and 30 pairs of sliding parts and switch bumpers should be lubricated. The connecting and moving parts on the heating rod should be lubricated according to usage.
5. Regularly inspect the pressure reducing, filtering, and oil mist triplets 24 to ensure that there is oil (sewing machine oil) in the oil mist and oil cup, and there is no water in the filter cup.
6. Keep the heating strip and silicone strip clean and free from foreign objects to avoid affecting the sealing quality.
7. The second layer of adhesive on the heating rod and under the heating plate serves as insulation. If there is any damage, it should be replaced in a timely manner to avoid short circuits.
8. The user provides their own working and inflating air sources. The working pressure of the vacuum packaging machine has been set to 0.3MPa, which is more suitable. Do not adjust it too much unless there are special circumstances.
9. The vacuum packaging machine is not allowed to be tilted or impacted during transportation, let alone placed upside down for transportation.
10. The vacuum packaging machine must have a reliable grounding device during installation.
11. It is strictly prohibited to put your hands under the heating rod to prevent injury. In case of emergency, cut off the power immediately.
12. When working, ventilate first and then power on, and when stopping, power off first and then cut off the gas.
Daily maintenance
Several key points for maintenance and upkeep of packaging machinery: cleaning, tightening, adjustment, lubrication, and anti-corrosion. In the normal production process, each machine maintenance personnel should strictly carry out various maintenance work according to the maintenance manual and procedures of the machine packaging equipment, within the specified cycle, reduce the wear rate of parts, eliminate hidden dangers of faults, and extend the service life of the machine.
Maintenance is divided into routine maintenance, regular maintenance (divided into first level maintenance, second level maintenance, and third level maintenance), and special maintenance (divided into seasonal maintenance and discontinued maintenance).
Routine maintenance
Centered around cleaning, lubrication, inspection, and tightening, routine maintenance should be carried out during and after machine operation as required.
The first level maintenance work is carried out on the basis of routine maintenance, with a focus on lubrication, tightening, and inspection of all relevant parts and their cleaning work
The second level maintenance work focuses on inspection and adjustment. Specifically, check the engine, clutch, transmission, transmission components, steering, and braking components.
The focus of Level 3 maintenance is to detect, adjust, eliminate potential faults, and balance the wear level of each component. Diagnostic testing and status checks should be conducted on parts that affect the performance of the equipment and those with signs of failure, in order to complete necessary replacement, adjustment, and troubleshooting work.
Seasonal maintenance
It refers to the inspection and repair of components such as the fuel lubrication system, hydraulic system, cooling system, and starting system for packaging equipment that should be emphasized every summer and before winter.
Stop maintenance
When packaging equipment needs to be discontinued for a period of time due to seasonal factors (such as winter vacation), cleaning, cosmetic surgery, matching, anti-corrosion, and other work should be done well.
Sealing and cutting method: bottom blade
Maximum outer diameter of membrane roll: DIA 250mm x W 470mm
Yield: 4-6 pcs/min
Fault resolution
The solution to the problem of the electromagnet not closing is to first check whether there is an internal or external problem with the host; Secondly, check the safety tube of the electromagnet to see if there are any signs of power on the electromagnet, eliminate mechanical jamming, and test the internal power supply when everything is normal; The common causes of such faults in weighing and packaging machines are: sensor damage, bridge voltage failure, incorrect circuit connection or interruption. The troubleshooting method is to detect the load signal of the sensor and wiring or the host, close and detect the bridge and amplification circuit or computer output display circuit, or remove the host, apply a reset signal through internal short circuit, determine whether the fault is inside the machine or from the switch, and then solve the problem.